Skip to content
TUNED RIDES
AI color-change render of a red Subaru BRZ — an illustration, not a Plasti Dip photo
AI render · Car Wraps
Car Wraps9 min read

How to Remove Plasti Dip: Peel It, Thicken It, or Dissolve It

By The TunedRides TeamPublished: Last updated:

Quick answer

How do you remove Plasti Dip from a car without damaging the paint?

Peel it. Lift an edge with a fingernail or a plastic tool and pull the coating back slowly in wide sheets. Plasti Dip is made to peel off cleanly, as long as it went on thick enough.

  • Plasti Dip calls 10–12 mils enough for most uses, which is about 4–5 spray coats. Thin dip tears into small bits.
  • Dip too thin to peel can be softened with a dip-dissolver product, then rinsed or wiped off.
  • Keep metal scrapers, razor blades and strong shop solvents off the paint.
  • Wheels and emblems peel the same way. Plasti Dip's own wheel guide calls for 4–6 coats.
Preview your next color on your own car before you dip again — free

Plasti Dip is a rubber coating in a spray can. People use it to black out wheels, badges and trim, or to change the color of a whole car for a season. The big selling point is that it comes off. Plasti Dip's own site says that, when it is applied properly, it "can be removed from most surfaces, if desired."

Note the condition in that sentence: applied properly. Dip that went on in thick, even coats peels off in long, satisfying sheets. Dip that went on thin comes off in a thousand tiny flakes, or not at all. This guide covers both cases. It also covers wheels and emblems, the tools to keep away from your paint, and the honest answer to how long Plasti Dip lasts.

The short version

  1. 1Wash the car so you are not dragging grit across the paint as you peel.
  2. 2Find an edge — a panel gap, a door edge, or the border of the dipped area.
  3. 3Lift it with your fingernail or a plastic trim tool. Never metal.
  4. 4Pull the dip back on itself, slowly, so it comes away as one wide sheet.
  5. 5If it tears into small bits, stop. It is too thin to peel. Go to the thin-dip fixes below.
  6. 6Pick off the leftover edges, then wash the car again and check the paint.

On dip that was sprayed thick, that is the whole job, and a panel can take minutes. Everything below is for the harder cases.

Why some Plasti Dip peels and some will not

It comes down to thickness. Plasti Dip is a film of rubber. A thick film holds together when you pull it, so the whole sheet follows your hand. A thin film does not have the strength to hold together, so it rips wherever you pull.

Plasti Dip gives the numbers in its own FAQ. In most uses, it says, 10 to 12 mils of thickness is enough, which it equates to 4 to 5 spray coats. Its spray directions say to apply 3 to 4 coats on average, as many as you like, with at least 30 minutes between coats. Its guide to dipping emblems adds one more line that matters here: for long-term use, apply more coats to improve durability and ease of removal later.

So if you are removing dip that someone else applied, you are really asking one question: did they use enough? The fastest way to find out is to try a test patch on a flat panel. One wide sheet means you can peel the whole car. Flakes and tears mean you are dealing with thin dip.

How to peel Plasti Dip, step by step

1. Wash first

Rinse and wash the car before you start. Dirt sitting on top of the dip gets dragged along as you peel, and edges of torn dip can drag it across the paint. A clean surface also makes it easier to see where the dip ends.

2. Start at an edge

Dip is easiest to lift where it ends: the border of a dipped area, a panel gap, or the edge of a door or hood. If there is no edge, you can make one. Press a strip of painter's tape hard onto the dip, then pull the tape up fast. It often brings a corner of dip with it. Avoid digging in with anything sharp.

3. Pull it back on itself

Once you have a flap, pull it back over the top of the dip, close to the surface, rather than straight up. Go slowly and keep the pull even. If the sheet starts to narrow or tear, move your grip back to where it is still wide. On a well-dipped panel you can take off the whole hood or roof in a few pieces.

4. Clean up the edges

Thin overspray around the edges of a dipped area tears more than the middle. Pick it off with your fingernail, or rub it gently with a soft microfiber towel. The dissolver route below also works for edges. Then wash the car again and look closely at the paint in good light.

When the dip is too thin to peel

This is the case almost every removal question is really about. The dip comes off in flakes the size of a fingernail, and a hood would take all day. You have three options.

Option 1: Make it thicker, then peel

This sounds backwards, and it is a common trick among people who dip cars. Spray several fresh, heavy coats of Plasti Dip over the thin layer. The new coats bond to the old ones, so when they cure, the whole stack comes off together as one thicker sheet. It follows the manufacturer's own logic: more coats, easier removal. Let it dry fully before you peel. Plasti Dip's spray directions give 4 hours as the minimum dry time before use. This option costs cans and an extra day, but it uses no solvent at all.

Option 2: Use a dip dissolver

Dissolver products are made for exactly this job. DipYourCar, a large Plasti Dip retailer, sells one called Dip Dissolver and describes it as a product that "will re-liquify Plasti Dip" to remove dip "that's too thin to peel." The seller recommends rinsing the softened material away with a pressure washer. Buyers in its reviews also report wiping it off with rags when they had no pressure washer. Those are the seller's and buyers' claims, not independent tests, so read the label on whatever product you buy and try it on a small, hidden area first.

Work one panel at a time. Spray the dissolver on, let it soak for the time the label gives, then rinse or wipe. Expect to repeat on stubborn spots. Keep the pressure-washer nozzle well back from the paint and away from panel edges and trim.

Option 3: Pay a shop

Detailers and wrap shops remove dip, and thin dip on a whole car is a long job. If the paint underneath is a respray, has chips, or you are not sure of its history, this is the safest choice. Ask the shop to check the paint before it starts, and to tell you about any risk.

What to keep off your paint

  • Metal scrapers and razor blades. One slip cuts the clear coat. Plastic tools and fingernails only.
  • Strong shop solvents. Plasti Dip lists naphtha, xylene and toluene for thinning dip and cleaning tools. It does not say they are safe on car paint, so do not use them as paint cleaners.
  • Abrasives. Scouring pads, rough sponges and polishing compound will take dip off, and the clear coat with it.
  • A pressure-washer tip held close. Keep the nozzle back, and never aim it straight into a panel edge or chipped spot.

One more caution. Dip only protects what was under it. If the paint had chips, rust or a poor respray before it was dipped, removal will show that, and peeling can lift loose paint along with the dip. That is not the dip's fault, but it is worth knowing before you start.

Removing Plasti Dip from wheels and emblems

Wheels are the most common thing people dip, and Plasti Dip's own wheel guide says that to remove the coating, you "simply lift an edge and peel." The same guide calls for 4 to 6 light, even coats when applying it, which is why most dipped wheels peel well. The edge to start from is usually the outer lip or the border of each spoke.

Wheels have two extra problems. Brake dust and wheel cleaners build up on dip, so wash the wheel well first. And the spaces between spokes are tight, so pieces tear more often. The thin-dip options above work the same way on wheels. If you plan to re-dip in a new color, our wheel visualizer lets you preview a finish on your own car first.

Emblems and badges are small and full of edges, so they can be fiddly. Plasti Dip's emblem guide uses fingers or a toothpick to lift overspray edges, which is far gentler on the paint around a badge than a blade. If you blacked out your chrome trim, our guide to chrome delete compares dip with vinyl and other options.

How long does Plasti Dip last?

Plasti Dip does not publish a lifespan for its coating on a car, so any exact number you see online is a guess. What the manufacturer does say is that the coating offers protection against UV rays, weathering and minor abrasions. It also warns that its fluorescent Blaze colors fade faster than other colors, even with a UV protector added.

In practice, how long dip lasts depends on how thick it went on, how much sun and road grit it sees, and how it is washed. Thicker dip lasts longer and peels more easily. If you are deciding between dip and a vinyl wrap, our guide to how long a car wrap lasts gives the figures film makers do publish, and how to remove a car wrap covers the other removal job.

Before you dip it again

Most people remove dip because they want a different color. Before you buy the cans, see the new color on your own car. The car color changer takes a photo of your car and renders it in a new color in about 30 seconds, free. It is a quicker way to rule out a color than spraying a panel.

And if you do dip again, remember the lesson from this guide: thick, even coats now are what make removal easy later.

Frequently Asked Questions

How do you remove Plasti Dip from a car without damaging the paint?

Peel it. Lift an edge with a fingernail or a plastic tool and pull the coating back slowly in wide sheets. Plasti Dip is made to peel off cleanly, as long as it went on thick enough.

Does Plasti Dip damage car paint?

Not on sound factory paint when it went on thick enough and is peeled off carefully. Plasti Dip says that when it is applied properly it can be removed from most surfaces. Problems come from the removal, not the dip: metal tools, abrasives, strong solvents, or paint that was already chipped or resprayed and lifts with the coating.

Why is my Plasti Dip coming off in small pieces?

Almost always because it is too thin. Plasti Dip says 10 to 12 mils is enough for most uses, about 4 to 5 spray coats. Thinner dip does not have the strength to hold together as a sheet. Either spray several heavy coats over it and peel the stack once it has dried, or soften it with a dip-dissolver product.

Can you use WD-40 or Goo Gone to remove Plasti Dip?

People do, and some report it works, but Plasti Dip does not list either product for removal. One buyer review on the DipYourCar Dip Dissolver page says Goo Gone worked but smeared the dip across the panel. Whatever you use, test it on a hidden spot first and wash the car afterward.

How do you remove Plasti Dip from rims?

Wash the wheel to remove brake dust, find an edge on the outer lip or a spoke, and peel. Plasti Dip's wheel guide says to simply lift an edge and peel. If the dip is too thin and tears, use the same fixes as on the body: add heavy coats and peel again, or soften it with a dip-dissolver product and rinse.

How long does Plasti Dip last on a car?

Plasti Dip does not publish a lifespan for car use, so treat any exact number with care. The manufacturer says the coating protects against UV and weathering, and that its fluorescent Blaze colors fade faster than other colors. Thickness, sun and washing habits make the biggest difference.

Can you remove Plasti Dip with a pressure washer?

A pressure washer is mainly used to rinse away dip that a dissolver has already softened, which is how DipYourCar recommends using its Dip Dissolver. On its own it can lift loose edges. Keep the nozzle well back from the paint and away from panel edges and chips.

Dip off and paint back? See a new color on your own car first, then buy the cans. Upload one photo and the new color is rendered in about 30 seconds.

Try it free — free →

No credit card required. Free tier available.

TR

The TunedRides Team

These guides are written and maintained by TunedRides. They cover car modification styles, what real builds cost, and how AI car rendering works — and they are updated as parts, prices and the tool itself change.